Looking for von mises stress simulation templates? Sign up for SimScale and join the largest engineering simulation community in the world! | Page 1

Verificacao de flambagem e falhas com 40 e 60 t.

* Strength and Structural analysis of a ladder foot step.

*Static Finite Element Analysis.

*Am performing a structural analysis to find maximum load bearing capacity of ladder foot step and also to verify the maximum  designated load of 3KN as well as it has to have a  factor of safety 2.5 and main the intention to find maximum stress acting area and redesign those area with respect to amount of deformation acting  on certain by optimising surface area at those regions.

Lifting Coupler static stress is simulated.

The engineering challenge is to predict how well the finished product will perform under real-world working conditions.
This involves considering stresses and deformation as well as a range of failure criteria. 
honeycomb Core is used in many applications like aircraft, buildings, etc.  in this particular simulation a honeycomb core is simulated against static structural by applying a load, pressure on different faces with different conditions such as cantilever or fixed beam.  
A most important analysis of this simulation is finding out of plane elastic modulus. Out of Plane analysis is done by applying load in a particular direction and finding deformation, stress, and strain in that particular direction.  Therefore three different times load is applied in x, y, and z-direction to simulate out plane analysis.  I here have taken two conditions first cantilever beam and the second is a fixed beam.
 It was very easy and interesting to simulate here and the time consumed was even less as compared to other software.

Engineering study of solar panels, including:

1. Wind loading and static structural analysis of a single panel

2. Transient wind analysis of a panel array

In this project static structural FEA of front upright of Formula Student Vehicle is carried out under loading conditions. 800 newtons of force is applied at the both upper and lower control arm and 5000 newtons of force is applied as brake force and the behavior of upright is observed for the further considerations and use in vehicle.

Beam Stress Analysis using FEA static analysis to determine the bending stress, axial tension and compression in the flanges, substantiations with hand calculation  to check the result for axial and shear stress .

 The geometry for the boundary condition is the same as for a cantilever beam, so one end is fixed  and the other one is free to move in space. You will see in this project 2 static simulation  because I wanted to see the differences applying the force on 2 different faces to see how SimScale model the load in the solver. Firstly, when I aplied the load in the top surface on the flange of the beam the solver saw a distributed load over the flange. The second static simulation had the same boundary conditions but now the load was applied on the Z- direction on the end face of the beam to simulate a concentrated force.

After I ran the simulation I tried to make some hand calculation to determine is the result were correct and also to determine the error compared to the analytical continuous problem. At the nodes of the mesh the errors were very small for engineering (10e-4) thus the results were good and model correct the reality. Von Misses stres was plotted to see if the material will yield or not, if you do not know what that is SimScale offers a great explanation on the website. SimScale is a great tool to model parts and assemblies with FEA, CFD or Thermal Analysis. For the hand calculation basic strength of materials courses were used, so it is possible for every user to understand the math behind. 

If something was unclear please leave a comment to make it work!

This simulation project aims to show the buckling of the column whose one end is fixed and force applied on the other end.

had to fix the beam head due to rotten wood and want to calculate the displacement and stress

model behavior of a string of beams with continuous and punctual loads and determine contact points with another other geometry.

stress and fatigue analysis of bucket excavator
structural analysis

Goal:
Evaluation and Comparison of Stress Distributed at Bone Implant Interface  with MiniScrew of Different lengths , inserted at different angles with different cortical thickness

Large Structure- Static Structural Analysis

Analiza statica liniara a unui brat de macara ce i se ataseaza o greutate de 12 T

This work aims to present the use of FEM in the analysis and design of an auxiliary device for the torque of the piston fixing nuts in hydraulic cylinders.

The aim is to dimension the mast of a light pole of 11 meters high with variable diameters. The implementation of the project will be in the patio of Raízen in Marabá-BR, located on the railroad.

The aim is to compare the clamping force of two headphones made using PVC and polypropylene.

The effect of the truss thickness on the maximum stress in the arm.

A model of a steel chain link is put on stress testing, provided the both ends are loaded . This test is a conceptual inspiration from cycle chains , it is that once the rider pedals his cycle each chain links undegoes a load distribution on them from pedals through socket on to the chain links and to the rear gear. The idea is simple and fun.

Pipe safety assessment against thermal load.

Evaluate different types of snap joint: Cantilever, U-Shaped, Torsional and Annular

This is a comparison between the results of Simscale and the hand calculus for a simple beam

In this project drop of a drone on a rigid plate was simulated.

Original project of @rszoeke