SimScale simulation projects by donvic | Page 1

donvic's profile

Structural Analysis & FEM of marine hose - Mesh Analysis and static load FEA -DonVic

Structural analsysis & FEA of Offshore Reeling Hose tests -static loads

Bending of an Aluminium and composite Pipe Simulation with FEA Nonlinear Non linear

Copper Wire Bending with Finite Element Analysis

Large Eddy Simulation of Flow over Cylinder Validation

Compressive analysis of offshore reeling hose spring -mesh attempt

FEA Offshore Reeling Hose tests -Internal Pressure static loads -ok

CFD of angle of attack on airfoil without dimple

Study the shielding effect of various cylinders in line

The aerodynamic effect of different angle of attack (AOA) on aeroplane wings

to study effect of dimples on lift generated by rotating golf ball to maximize the range of it. I am going to do the simulation on CAD of various golf balls. I'll use use k-epsilon in-compressible flow equation.

studying the size of cavitation in order to achieve minimum drag coefficient on water submerged body

FEA Master Class Session 3 handout: In this project the drop test of an iPhone 6 has been performed with and without case. It is as in handout

step_by_step_tutorial_of_full_car_f1_aerodynamics_2017

This project simulates instantaneous turbulent wake of a cylinder body via LES method.

The air flow around a football is simulated with focus on the effects of the pattern on the football surface and spinning of the ball.

This project involves the CFD simulation of micro wind turbines

The air flow around a football is simulated with focus on the effects of the pattern on the football surface.

The air flow around a football is simulated with focus on the effects of the pattern on the football surface and spinning of the ball. Rotation on  with MRF zone is also included

Thermal Comfort Analysis in a Theater Room and CHT

Thermal Comfort Analysis on Onboarding Training

The current project involves conducting a Computational Fluid Dynamics (CFD) analysis of the airflow inside the data center with the help of the SimScale platform. The goal is studying the airflow patterns and designing the ventilation system, we simulate a sample meshed geometry of the data center along with preset boundary conditions.
 
Our results will reveal a deeper insight into the further steps needed to be taken to make design alterations or the data center and/or the ventilation system. Research paper on Data Center -by Gao et al.  and originally setup by @sjesu_rajendra

This project involves the simulation of ventilation in an aircraft cabin. There are 6 comparison configurations with 3 different inlets and 2 outlets.

Analyse the duct positioning to have effective ventilation system

Aerodynamics of a soccer ball, La Paz H... 3637m Density... 0.85
Nogometna zoga, Bolivia .... this model is optimised to visualise the aerodynamics of the football

FEA Offshore Reeling Hose tests -static loads -ok

CFD of aeroflow winglet with dimple with VIV

Project to validate the resistance of a ship hull / vessel under different conditions. Multiphase flow simulation. Turbulent and Laminar.

This is a model to help a Simscale user, as it was just a geometry with detail of a floating fender (couped steel pipe welded to much larger steel pipe, welds included). Somethings are unsure in this model.

At this stage, you can add the material properties. Since it is a fender, my guess is that you will use rubber and steel materials. As such, you can do a Finite Element Analysis to see stress analysis with nonlinear or linear case, depending on what you need. However, based on the use as floating offshore fender, I suggest that you start with that. You have welded both pipes but one end is open and I do need see how itfloatings if the curved sheet faces up. You may need to look at existing fender designs... as it should be closed if it will be down, unless you are wleding it to a ship or an offshore structure. 

As for the analysis, you can apply the needed loading conditions you need, such as pressure load of about 6000 Pa or 7000 Pa, fixed end, and if you are doing an impact study, you need to add another material for the boat or ship. 

You can see academic papers on Fender analysis or Global Analysis of FPSO and fenders or for Shuttle Tankers During Side-by-Side Offloading and fenders.  Hope that helps!

with detail of a floating fender (couped steel pipe welded to much larger steel pipe, welds included)

Structural Analysis of a Bowling Strike with respect to the correct placement of the bowlings and the striking velocity given

Public Profile

donvic's profile