SimScale simulation projects by aarafat_7 | Page 1

aarafat_7's profile

This project shows the bending of an Aluminium pipe through rolling process.

Rubber Compression-Oring-Static nonlinear Hyperelastic

Checking the sealing fitting process on a quarter symmetry model with and without friction. This is a sample hyperelastic rubber material using the Mooney-Rivlin model. Results of interest are the required fitting force as well as the contact state and pressure. - Copy

Pedestrian Wind Comfort Analysis for assessing wind speed through the city of Rotterdam

Thermal Comfort Analysis in a theater Room

This project shows the bending of an Aluminium pipe through rolling process. - Copy

This project takes a standard grasshopper model used to demonstrate outdoor thermal comfort, to demonstrate how to import SimScale Results back into the grasshopper engine for visualization and calculation purposes such as calculating UTCI. - Copy

Demonstration project of an electronics enclosure using CHT v2. Comparison different passive heat sink designs and comparison of active and passive cooling - Copy - Copy

This project demonstrates the static stress analysis of aircraft engine bearing bracket models considering both linear and nonlinear material definition.

Thermal Comfort Workshop - Office space - Solar Radiation - Copy

Structural simulation according to UN 38.3 T3 vibration test criteria - Copy

Static-Linear structural analysis of a loaded mechanical arm with multiple contacts.

wind comfort study for London area of walkie talkie building

Simulations with custom boundary condition types and tabular data upload - Copy

Example project of a multiphysics application. A Static and a Frequency analyses are used to determine the structural behavior of the assembly. Then, a conjugate heat transfer analysis will determine the thermal behavior of the cooling process of the motor. - Copy

Thermomechanical  Analysis of a Spark Plug-Demo

Cover is offset by 0.005 meter, 2 snaps, 
Assumptions : Symmetric on both planes.
Only a quarter portion of enclosure is analysed. - Copy

In this project, a thermal shock analysis of a globe valve is performed along with a flow analysis and a structural analysis -

Internal Natural Convection Electronics Cooling Demo 2

FSAE Battery Pack - Joule Heating Demo - Copy

Demonstration project of an electronics enclosure using CHT v2.

This project simulates water flow through a Gate valve by using the Incompressible flow simulation type. Main purpose of the project is to obtain the forces acting on the half-open valve and flow pattern through the pipe as it crosses the valve section. - Copy

An example of using SimScale's Convective analysis type to perform steady-state Data Centre problems.

Raised Floor Data Center - Webinar - Copy

this project goal is to evaluate the difference in cooling effectiveness between series and parallel cooling tube of an EV Battery Module.

The cooling strategies used to maintain the battery under 40C are cooling tubes places between the rows of cells. Inside the aluminium channel extrusions flows a coolant made of water and glycol.

Subsonic multiphase project on oil filter from Jon

This is a sample project showing how to perform a bolt preload analysis on a bolted flange model.  
For this particular project, sweep mesh controls are utilized, in order to create better quality elements ensuring low total node count.

The project consists of a 45deg flange segment simulation as well as the full flange simulation model.

This project demonstrates the static stress analysis of three aircraft engine bearing bracket models considering both linear and nonlinear material definition. The models are tested with horizontal and vertical loading conditions as provided on the challenge page of GrabCAD.

In this tutorial, the transport of exhaust gases into the atmosphere is simulated. Gases will come out of two chimneys of a plant.

Wind Comfort Analysis in a sample city partly on a hill.

This tutorial project aims to showcase how to set up and run a simulation for a pump geometry. The subsonic meshing tool was used with coarse meshing.

Ventilation design for better Contaminant Fume extraction

This simulation aims a determining whether the temperature of the board of 2x 160W COB Series UV LED is below the recommended temperature of 40C  with a water cooling block running with 0.2m/s inlet velocity.

3D model from Philippe Cavalier (https://grabcad.com/library/water-cooling-led-heatsink-1)

A small part of the SimScale office . We actually don't have any active cooling here (Germany) so we took a few liberties to make this more interesting!

Public Profile

aarafat_7's profile