SimScale simulation projects by ErmoB | Page 1

ErmoB's profile

This project is aimed at creating a parametric analysis of heat distribution within a 3D printer.

This project is the starting point for the homework for Session 1  of  the Baja SAE workshop. It enables the user to analyse the plastic deformation in an All Terrain  Vehicle (ATV)  Suspension .

Harmonic Analysis of Complete 3D Printer Assembly

Study of type of noise barrier for aerodynamic factor

Study of vortexes on sound-absorbent barriers. More solutions are evaluated to study the correct cp value to be used in the calculations.

Tutorial project for a flow analysis of a pipe junction. The project only provides the geometry to start with. See our tutorials section to have a look at the step-by-step instructions to set up the simulation.

Cp factor for wind barrier for height 3m, 4m, 5m and 6m

Study of types of noise barriers terminals

Analysis of situations for concentrated loads, L-profile, plates and holes

Wind study in an isolated and continuous ground photovoltaic system with 2 pole structure.

Wind on photovoltaic system fixed to ground study flow

This is used as a starting point for the SimScale Users and participants of the Session  2 of the All-Terrain Vehicle Design Workshop

Our aim is to investigate the heat transfer through the assembly to get insights about the temperature distribution
within the extruder. This will help us on the one hand to understand the extrusion process itself and in addition also
help us to verify the position of the temperature sensor for the closed-loop control system of the extruder.

Incompressible Fluid Flow analysis of two globe valves

In this exercise, you will perform a simple heat transfer analysis on the SimScale Platform and then compare the results to a hand-calculated solution.

In this exercise, you will use linear static analysis to analyze several configurations of an aircraft engine bracket under a vertical load.

Study of influence of L/H value in wind barrier sound acoustic

The effect of numerics on the simulation quality and convergence time.

Valutazione del vento nel caso di barriera fonoassorbente

This meshing tutorial shows how to setup the Tetrahedral automatic, Tetrahedral parametric and the Tetrahedral with local refinements for a structural analysis simulation.




FEA Master Class Session 3 handout: In this project the drop test of an iPhone 6 has been performed with and without case.

Webinar Project- Carotid Artery Bifurcation
The project simulates the flow of blood as a non-newtonian fluid through a realistic Carotid Artery Bifurcation. Simulation are performed for 3 cases- of a healthy blood vessel  with no calcification or blockage and through an moderately and severely calcified or blocked blood vessel. 
The results show the differences in pressure, velocity profile and the outlet flow  through the 2 branches.

Flow conditions are based on a paper: STUDY OF BLOOD FLOW IN A BIFURCATION WITH A STENOSIS,
Sonia I.S. Pinto, E.D. Costa, J.B.L.M. Campos, J.M. Miranda

Effect of number of propeller blades on the lift od the Drone

Since our drone consists of different components from different materials, they have to be connected somehow. In thiscase we are manly using screws to connect these parts. One of the most loaded connection is the one between the dronearm and the two base plates.

Related to step-by-step tutorial of the biomedical workshop (session 2) https://www.simscale.com/forum/t/biomedical-engineering-workshop-session-2-analysis-of-cardiovascular-stent/36862

Related to step-by-step tutorial of the biomedical workshop (session 1)

https://www.simscale.com/forum/t/biomedical-engineering-workshop-session-1-stress-shielding-in-a-hip-joint-prosthesis/36830/3

In this exercise, you will complete a laminar pipe flow analysis

In this exercise, we will consider the deflection of a cantilever beam with a concentrated load at the free end. We can calculate the deflection by hand and via a static analysis using the SimScale platform.

Public Profile

ErmoB's profile