SimScale simulation projects by AnnaFless | Page 1

AnnaFless's profile

This project demonstrates the Nonlinear Static Analysis of an Airplane Bracket

Tutorial project for a stress analysis of a connecting rod. The project only provides the geometry to start with. See our tutorials section to have a look at the step-by-step instructions to set up the simulation.

This project demonstrates the hip joint prosthesis for the femur bone. Several types of materials are tested for the hip joint in this case including Co-Cr-Mo on Ti-6Al-4V, Co-Cr-Mo on UHMWPE and Concrete on Concrete.

In this exercise, you will perform a simple heat transfer analysis on the SimScale Platform and then compare the results to a hand-calculated solution.

This project demonstrates a Dynamic Analysis of a Simplified Crank-Piston Mechanism with Frictionless Contacts.

In this exercise, you will use linear static analysis to analyze several configurations of an aircraft engine bracket under a vertical load.

In this exercise, you will complete a laminar pipe flow analysis

In this exercise, we will consider the deflection of a cantilever beam with a concentrated load at the free end. We can calculate the deflection by hand and via a static analysis using the SimScale platform.

Consider fluid flowing through a circular pipe with 2 inlets and 1 outlet

FEA Master Class Session 3 handout: In this project the drop test of an iPhone 6 has been performed with and without case.

Tutorial project for setting up the mesh using Hex-dominant automatic for external flow.

FEA in Formula Student and Formula SAE Workshop Session 1: Wheel Upright from a Formula SAE/Student vehicle.
https://www.simscale.com/fea-formula-student-sae/

Stress analysis of a reclaimer arm under a load

Related to step-by-step tutorial of the biomedical workshop (session 1)

https://www.simscale.com/forum/t/biomedical-engineering-workshop-session-1-stress-shielding-in-a-hip-joint-prosthesis/36830/3

Webinar Project- Carotid Artery Bifurcation
The project simulates the flow of blood as a non-newtonian fluid through a realistic Carotid Artery Bifurcation. Simulation are performed for 3 cases- of a healthy blood vessel  with no calcification or blockage and through an moderately and severely calcified or blocked blood vessel. 
The results show the differences in pressure, velocity profile and the outlet flow  through the 2 branches.

Flow conditions are based on a paper: STUDY OF BLOOD FLOW IN A BIFURCATION WITH A STENOSIS,
Sonia I.S. Pinto, E.D. Costa, J.B.L.M. Campos, J.M. Miranda

Effect of Boundary Layers and possible improvements
try to reduce numbers of cells for faster computation

Cooling plate - Session 2 FEA workshop for Formula Student

Consider fluid flow through a pipe with 2 inlets and 1 outlet

Our first attempt didn't work with a .STL file, we'll try it with an IGES file.

Simulations of NACA 0012, NACA 2410 and NACA 64-108 from -15 degrees of angle of attack to 15

Weight is one of the most critical parameters in aircraft design. In this exercise, you will be provided with a baseline design of an aluminum aircraft wing. Your objective is to reduce the weight of the wing without exceeding the yield stress and maximum allowable deflection

In this project, a Dynamic Analysis was done to determine the physical behavior of a carabiner subjected to displacement along its strong axis. 

Weight is one of the most critical parameters in aircraft design. In this challenge, you will be provided with a baseline design of an aluminum aircraft wing. Your objective is to reduce the weight of the wing without exceeding the maximum allowable deflection (+ y direction) of .90 meters.

In this project two different mounting brackets were modeled using harmonic analysis

Tutorial project for a flow analysis of a pipe junction. The project only provides the geometry to start with. See our tutorials section to have a look at the step-by-step instructions to set up the simulation.

This project includes everything you need to get started with the homework assignment of our makers workshop

This skateboard simulation project tests the durability of a skateboard when it lands on the ground with a rider on it. This project was presented for the Using SimScale with Autodesk Fusion 360 Webinar. A step-by-step by tutorial can be found here: https://www.simscale.com/forum/t/step-by-step-tutorial-impact-analysis-of-a-skateboard/37430

This project contains a mesh and a simulation setup of an external aerodynamics analysis for the GO WITH THE FLOW CHALLENGE

This meshing tutorial shows how to setup the Tetrahedral automatic, Tetrahedral parametric and the Tetrahedral with local refinements for a structural analysis simulation.

Public Profile

AnnaFless's profile