SimScale simulation projects by Ali_Arafat | Page 1

Ali_Arafat's profile

The project illustrates how to simulate airflow around a complex F1 vehicle. Incompressible flow simulation type is chosen to simulate the flow pattern around the vehicle. Main outputs of the simulation are pressure distribution around the lifting surfaces of the vehicle, aerodynamic flow coefficients and velocity streamlines.

HPAC webinar project for Blade variation study of a Radial Fan is presented. Two design configurations for the Radial Fan is chosen, and both configurations are simulated in three different operating conditions. Main purpose of the project is to assess the pressure rise within each configuration and consequently compare flow coefficients.

This project simulates the flow inside a car cabin. Convective Heat Transfer simulation type is used to obtain the flow behavior and thermal changes inside a car cabin. Mean age of fluid parameter is also observed to obtain the overal air quality inside the car cabin.

This project simulates water flow through a Gate valve by using the Incompressible flow simulation type. Main purpose of the project is to obtain the forces acting on the half-open valve and flow pattern through the pipe as it crosses the valve section.

This project takes a standard grasshopper model used to demonstrate outdoor thermal comfort, to demonstrate how to import SimScale Results back into the grasshopper engine for visualization and calculation purposes such as calculating UTCI.

This project simulates a Centrifugal water pump with MRF approach

This project analysis the cooling of a PCB board via CHT

Air Conditioning and Ventilation Webinar Session 4. Ventilation design of a 3 Clean Room configurations is analysed via Laminar Steady State simulations with scalar quantity.

This project simulates airfow around a Semi-Truck with container trailer.

This project simulates instantaneous air flow around an Aircraft Landing Gear.

Radial - Centrifugal forward curved fan performance CFD analysis project

This project simulates Scalar Transport mixing in turbulent T-Junction pipe flow.

This project simulates opening of a pressure relief valve using 6 DOF body motion.

HPAC Webinar-Duct Flow Analysis and Design Optimization

Convective Heat Transfer application for room heating.

This project simulates flow around a rotating keel of a sail yacht.

EuroAVIA-Workshop Session3 -Aerodynamics of an Aircraft. This project simulates air flow around an Aircraft at low sub-sonic compressible flow regime.

The purpose of this project is to investigate and mitigate Vortex Shedding around a 50-story tall building at high wind speeds of 45 m/s. The building is 150 m tall and has a fixed square cross base of 20 x 20 m. Two designs are analysed, initially with sharp-corners and the optimized with Corner Softening using rounded-corners. To study the dynamic effects of wind loading, a Transient analysis with Incompressible Turbulent flow is performed.

A Multi-phase flow simulation for filling of a vehicle fuel tank that is initially filled with Air.
Originally done by dheiny.

This project is part of session 1 of the Air Conditioning and Ventilation webinar. It shows how the cooling of a Data center room can be simulated using SimScale.

This project simulates instantaneous turbulent wake of a cylinder body via LES method.

Passive and Active convection cooling of a Raspberry Pi mother board design .

Automotive Catalytic Converter exhaust flow analysis using Porous Media.

This project simulates a Centrifugal Pump with a rotating mesh using Arbitrary Mesh Interface - AMI - approach.

This project simulates incompressible non-newtonian flow through a sudden expansion.

This project simulates air flow around an Aircraft at low sub-sonic compressible flow regime.

Flow analysis of an automotive carburetor

The project simulates the spread of gas in an office room via Passive Scalar Transport.

This project simulates air flow through a Centrifugal Compressor.

Support case for project careen by lisandromaders 

Tutorial project for  Incompressible, turbulent airflow around a frontwing

Sample project for flow through a textile fabric done by SimScale

This project simulates a water purification process in a maze channel reactor.

Webinar project for Air-Conditioning and Ventilation Session 2

FSAE-Workshop Session-2 Homework project for aerodynamics of complete Formula Student Race Car

This project simulates sloshing of fuel inside a moving fuel-tank.

This project simulates convective flow inside a Light Bulb.

6 DOF validation test for free heave motion of floating cylinder

This project simulates incompressible flow through an industrial scale Butterfly Valve.

This project simulates flow in a mixing-diffuser for juice flushing.

This project simulates flow of water through a spillway.

This project simulates water flow through a double flanged check valve.

FSAE workshop session 1-Front Wing Analysis homework tutorial project.
For Step-By-Step see: https://www.simscale.com/forum/t/step-by-step-tutorial-homework-of-session-1/52675

Tutorial project for a thermal analysis of a differential casing. The project only provides the geometry to start with. See our tutorials section to have a look at the step-by-step instructions to set up the simulation.

This sample project shows how to simulate particle fluid flow through a cyclone separator.

Tutorial project for a flow analysis of a pipe junction.The project only provides the geometry to start with. See our tutorials section to have a look at the step-by-step instructions to set up the simulation.

Public Profile

Ali_Arafat's profile