# Step-by-Step Tutorial Session 1 - Front Wing Design Study (Part 1)

**URL:** <https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755>\
**Category:** Formula Student/SAE Workshop - 2017\
**Created:** [August 28, 2017, 2:26pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755 "2017-08-28T14:26:21Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![drodriguez32](https://www.simscale.com/forum/user_avatar/www.simscale.com/drodriguez32/32/14276_2.png) [@drodriguez32](https://www.simscale.com/forum/u/drodriguez32)\
**Post date:** [August 28, 2017, 2:26pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/1 "2017-08-28T14:26:21Z")

</div>

## Recording

* * *

## Homework Submission

For your homework, your task is to investigate the behavior of drag and lift and determine the stall zone for two different front wing flap angles: 6 degrees (standard) and 18 degrees (high downforce) considering a constant inlet velocity of 20 m/s.

The step-by-step tutorial below contains all of the steps for setting up the simulation in SimScale and visualizing the results.

To submit your homework assignment, please generate a public link of your project ([Sharing a Project](https://www.simscale.com/forum/t/sharing-a-project/242))

**Homework Deadline** : The homework deadline has been extended until **September, 26th 11:59 pm CEST**

#### [Click Here to Submit your Homework](https://marketing.simscale.com/acton/form/14483/00d1:d-0001/1/-/-/-/-/index.htm)

* * *

## Outline

**PART 1:**

1. Introduction

2. Project Import

3. Mesh Generation  
a. Geometry Primitives  
b. Mesh Refinements  
c. Start Operation  
d. Additional Meshes  
e. Mesh Quality

4. Simulation Setup  
a. Analysis Type  
b. Domain  
c. Initial Conditions  
d. Boundary Conditions  
e. Numerics  
f. Simulation Control  
g. Result Control  
h. Simulation Runs  
i. Additional Runs

5. Recommendations About Comments

**PART 2:**

1. Post Processing  
a. Filters/Visualization  
b. Additional Features

2. Homework Link

3. Result Comparison  
a. Standard vs High Downforce

* * *

## Introduction

This is part one of the step-by-step tutorial. In this part you will be guided through the meshing setup and simulation setup. In the second part you will be guided through the post-processing of the results and we will visualize and analyze some results.

Lets dive in!

In this tutorial, you will be doing a full fledged flow simulation of the aerodynamics of a front wing. The focus of this simulation is to investigate the drag and lift forces on the wing and identify flow separations.

For your homework, your task is to investigate the behavior of drag and lift and determine the stall zone for two different front wing flap angles: 6 degrees (standard) and 18 degrees (high downforce) considering a constant inlet velocity of 20 m/s.

Let’s take a look at the physics of the front wing before we start to set up our simulations:

 ![](https://www.simscale.com/forum/uploads/default/original/2X/1/1bd4b24ecadb2dd0cef76c3a0a0cc63728adcd4a.png)

As a first simplification we can exploit the symmetry of the front wing. Simulating only half of the wing reduces the computational effort by defining the inner surrounding wall (brown) as a symmetry plane.

The body of the wing is a physical wall (grey), which means that it involves friction and should be defined as so-called “no-slip walls”.

The outer (not visible here) and upper surrounding walls (dark blue) are necessary to limit the size of the domain we want to simulate since we are not able to simulate an infinitely large domain. In reality, these walls do not exist and should not interact with the flow. A good approximation here is to assume this wall as frictionless or so-called “slip walls”.

The bounding face on the right-hand side (red) will be defined as an inlet with a constant flow velocity profile.

The bounding face on the left-hand side (green) will be defined as an outlet with a constant pressure.

These four bounding walls define the size of the fluid domain, and in general you have to reach a compromise: you want these walls as far as possible so that you can observe all the fluid behavior (also, if they are too close to your geometry you might get strange results), but you also want to limit your fluid domain to save computational power.

In reality the car is in motion, so there is no relative motion between the air and the floor. Because here the car will be standing still and the air will move around the car, to maintain the condition that there is no relative motion between the air and the floor we will apply a wall velocity on the lower bounding wall (cyan).

You will simulate two different wing set-ups for which the geometry is provided.

First we will start with the **Standard Configuration** and follow all the steps in detail. The other configuration(s) will follow the same procedure and therefore will not be documented in detail.

##### _ **General notes:** _

1. _ **Most of the descriptions will be below the images.** _
2. _ **For many attributes, SimScale sets some default values that don’t need to be changed unless specified. Please double check your procedure with the screenshots** _

* * *

## Project Import

To start this exercise, please import the project into your workspace by clicking on the link below:

> **[SimScale Login](https://www.simscale.com/workbench?publiclink=fddf42d0-12fd-4e6a-8310-5638e6898a0c)**
>
> Log in to your SimScale account. SimScale makes high-fidelity engineering simulation technically and economically accessible. At any scale. In the cloud.

If the project appears to be private, please make a copy of it to work on it.

* * *

## Mesh Generation

For this tutorial we will work with the _Standard_ model for which the flap has an angle of attack of 6 degrees.

 ![](https://www.simscale.com/forum/uploads/default/original/2X/5/58717940c2370089c535bfc1e7cf141490d7d104.png)

Start by clicking on the **FW - Standard** model under _Geometries_ in the navigator. Then click on **New Mesh** to start creating a new mesh on this geometry (this doesn’t start the mesh operation, you still have to go through all the settings).

 ![](https://www.simscale.com/forum/uploads/default/original/2X/1/140247e0363cd8c6ab86d476eb617b87adf6c0f5.png)

The new mesh operation will be generated automatically. Next change:

1. Set the **Type** to **Hex-dominant parametric (only CFD)**.

2. Configure the _Bounding Box geometry primitive_ to the following:  
**Number of cells in x direction to 60**  
**Number of cells in y direction to 16**  
**Number of cells in z direction to 16**

3. Set the **Number of parallel computing cores** to **16**

4. Scroll down to change other values to optimize the meshing parameters

5. **Cell limit for refinement termination** to **15**

6. **Max iterations for meshing algorithm** to **100**

7. **Max iterations for mesh conformation** to **1**

8. **Max face aspect ratio for layers** and **Max ratio of layer thickness to medial length** to **0.6** and **0.4** respectively.

9. **Max overall iterations for layer addition** to **3**

10. Click **Save** to register changes.

### Geometry Primitives

#### Background Mesh Box

Next, under _Geometry Primitives_ select **Background Mesh Box**.

 ![](https://www.simscale.com/forum/uploads/default/original/2X/3/3e6947cd61b1ed082856e82386869a8cc0c810a6.png)

Change the setting accordingly:

- **Min. Point (x)** = - 3.6
- **Min. Point (y)** = .003
- **Min. Point (z)** = - 0.6
- **Max. Point (x)** = 6
- **Max. Point (y)** = 2.403
- **Max. Point (z)** = 1.8

Here you are defining the size of the fluid domain.

Click **Save**. If you don’t see the entire box click on the reset icon over the viewer to see the created mesh box.

#### Material Point

 ![](https://www.simscale.com/forum/uploads/default/original/2X/b/b4e8bab2ef64f021ce3fc6d77373e77d43436305.png)

Next you will specify the material point. This will tell the platform where the mesh will be created, so make sure it is inside the Background Mesh Box but outside of any solid (if you leave it inside the wing the platform will think you want to do a simulation of the flow inside the wing). Input these values:

- **center (x)** = - 1.5
- **center (y)** = 0.5
- **center (z)** = - 0.5

Then click **Save**

#### Cartesian Box - Outer

 ![](https://www.simscale.com/forum/uploads/default/original/2X/c/c1347a920b8fcbcb163b892b87497c85c0787d21.png)

Next go back to **Geometry Primitives** and click on **+ New** and then **Cartesian Box Outer** to define a new Cartesian Box that will be used to define a mesh refinement region.

 ![](https://www.simscale.com/forum/uploads/default/original/2X/d/de23577d9872e5552a218d573619670ab4d6c3ea.png)

After creating a new Cartesian Box, you will be directed to the definition of this Cartesian Box. Change the dimensions of the box to the following:

- **Min. Point (x)** = -2.2
- **Min. Point (y)** = .003
- **Min. Point (z)** = -0.6
- **Max. Point (x)** = 3
- **Max. Point (y)** = 1.5
- **Max. Point (z)** = 1

Click **Save** to register your changes.

#### Cartesian Box - Inner

 ![](https://www.simscale.com/forum/uploads/default/original/2X/0/017a405e4fd69c9cfa53950e5f2c3743b58f65e8.png)

Follow the same procedure to define another Cartesian Box for further refinement definitions. Rename it to **Cartesian Box Inner**. This time change the values to the following:

- **Min. Point (x)** = - 1.8
- **Min. Point (y)** = .003
- **Min. Point (z)** = - 0.6
- **Max. Point (x)** = 1
- **Max. Point (y)** = 0.9
- **Max. Point (z)** = 0.4

Click **Save** to register your changes

With these Cartesian Boxes that we created we will define _refinement regions_ where cells will be smaller and thus we will be able to observe more detail in the complex areas of the flow - a mesh that is too coarse will not allow you to observe small flow structures.

### Mesh Refinements

 ![](https://www.simscale.com/forum/uploads/default/original/2X/1/1c6236b88cdea12396dde84f76e17b2e417ab1b3.png)

**A good mesh requires well defined refinements**. Now we will start creating the mesh refinements. For this proceed to **Mesh Refinements** and click **+New**

_ **How does a mesh refinement work?** _ It divides each cell to create more, smaller cells, and each level of refinement applies this to the cells generated in the past refinement level. This means that each cell that is refined will be divided into 4 smaller cells for each level. Example: at level zero you have 1 cell, at level one you have 4 cells, at level two you have 16 cells, at level three you have 64 cells, and at level four you will have 256 cells.

#### Mesh Refinement 1

 ![](https://www.simscale.com/forum/uploads/default/original/2X/e/ea0d97dfdf5b5462ff47bbfee09ee81422399841.png)

Rename it to **surf-wing-flap** (optional).

Change the **Type** to **Surface refinement** and then both **Level min** and **Level max** to **7** respectively.

Select the main wing and the flap - you should see that under _Refined surfaces_ **FWing** and **flap** should be selected.

With this refinement we are improving the mesh that sits directly on the surface of the geometry. We do this to capture more accurately more details of the geometry and to better observe how the flow interacts with the surface of the wing.

Click **Save** to register your changes.

#### Mesh Refinement 2

 ![](https://www.simscale.com/forum/uploads/default/original/2X/7/7321075b899c39bd40ab073ffbb723c95035c755.png)

Following the same procedure, create a new refinement and name it **feature** (optional).

Under _Refinement levels_ change **Distance** and **Level** to **0.001** and **7** respectively.

This refinement specifies that at a distance of 0.001 m from every edge and corner the mesh will be refined up to level 7. Again, this helps us capture the most complex features of the geometry and get better results around these areas.

Then click **Save**

#### Mesh Refinement 3

 ![](https://www.simscale.com/forum/uploads/default/original/2X/a/aadaecd5603359f50fc39c705a1304478cf66a87.png)

Now we will start refining the regions (Cartesian Boxes) that you created earlier.

Create a new refinement and rename it to **region-inner** (optional). This will be the smaller Cartesian Box.

Change **Type** to **Region refinement** and then under _Refinement levels_ change **Level** to **3**

Select **Cartesian Box Inner** under _Geometry Primitves_ and click **Save** to register the refinements for this specific Cartesian box.

This is the region closest to the wing, so flow structures will be more complex immediately around and after the wing. So we want this area more refined.

#### Mesh Refinement 4

 ![](https://www.simscale.com/forum/uploads/default/original/2X/e/e734e8ce84b6b54882e043ae4540b5c9d1244588.png)

Create a new refinement for the other Cartesian Box. This time rename it to **region-outer** (optional).

Change **Type** to **Region refinement** and then under _Refinement levels_ change **Level** to **1**

Select **Cartesian Box Outer** under _Geometry Primitves_ and click **Save** to register the refinements for this specific Cartesian box.

Further away from the wing we won’t have such complex flow, but because we are still considerably close and the flow is still affected we want this region slightly refined as well.

#### Mesh Refinement 5

 ![](https://www.simscale.com/forum/uploads/default/original/2X/b/b47d3d71816d2ef09e50ec00475b0c03644c28f6.png)

Next we will add layers over the surfaces on the whole wing and the floor. Layers will create small cells along every face of the geometry and allow us to capture the results near the surfaces (like the development of the boundary layer) more accurately.

Create a new refinement and rename it to **Layer-wing** (optional).

Change **Type** to **Inflate boundary layer** and then change **Expansion ratio for layer cell thickness** and **Minimum overall layer thickness [-]** to **1.8** and **0.0001** respectively.

The expansion ratio defines how fast the boundaries will grow - how much larger the next boundary cell will be compared to the past. And the minimum overall thickness defines a minimum limit to the size of the boundary layers - if the overall thickness is below this number, the algorithm will consider it not significant and no layers will be added.

Select the main wing and the flap. Under _Surfaces with layers_ you should see **FWing** and **flap** are selected.

Click **Save** to register your changes.

#### Mesh Refinement 6

 ![](https://www.simscale.com/forum/uploads/default/original/2X/5/5ad2a36e1016736deadaa8d98e5a7989117209a2.png)

For the floor layers, create a new refinement and rename it to **Floor-layer** (optional).

Change **Type** to **Boundary box layer addition**

Change **Bounding box face** to **Zmin** and then the **Number of layers** and **Thickness of the final layer [-]** to **3** and **0.35** respectively.

Here we are creating boundary cells like in the past refinement, but these are applied to the floor.

### Start Operation

 ![](https://www.simscale.com/forum/uploads/default/original/2X/7/779dd2458e53ee357f9b74378b4aceeecfcc8817.png)

Once you have defined all of the mesh refinements, go back to the **Operation 1** and click **Start** in order to submit the meshing job to the server. Due to the fineness of the mesh, the meshing could take around 30 minutes to finish. When the meshing is done you will see a green sign that says **FINISHED** when you click on your mesh.

### Additional Meshes

 ![](https://www.simscale.com/forum/uploads/default/original/2X/9/948e8b9194b6b6ff2970f88a616a07334bb7d1b2.png)

While the first mesh job is running, take advantage of parallel computing and proceed to start setting up the other configuration(s). You don’t have to perform all the meshing operations again from scratch. Just duplicate the already created mesh by right clicking on it and then click **Duplicate**.

 ![](https://www.simscale.com/forum/uploads/default/original/2X/2/2483a2d5a5f3153788edae6a4c718f113dc44463.png)

Rename the duplicated mesh and use the drop-down to change the **Base Geometry** to the model other model. Then click **Save**. Now you will have to reassign the **Fwing** and **flap** faces for **surf-wing-flap** and **Layer-wing** refinements and start the meshing operation.

### Mesh Quality

 ![Mesh quality](https://www.simscale.com/forum/uploads/default/original/2X/5/51007c8164a0a215601df28d2a5bdae5368888b9.png)

When your meshing process is done, don’t look at the **Mesh Operation Event Log**. If you want to check the quality of your mesh please click on **Meshing Log** in the _Navigator_ and scroll to the bottom of the text log. There should be around 7 illegal faces (like in the picture) - don’t worry, as long as the number of illegal cells is close to the picture, your simulation will run.

* * *

## Simulation Setup

 ![](https://www.simscale.com/forum/uploads/default/original/2X/9/9c6891c43784606f5cd5cd479263b6bf513c64d0.png)

Once the meshing of the first geometry is finished, you can proceed to **Simulation Designer** without waiting for others to complete in order to set up the simulation in parallel.

 ![](https://www.simscale.com/forum/uploads/default/original/2X/a/a750371983c3dbdc9b26dd907814294d3c1834f0.png)

Once you are in **Simulation Designer** , click **New Simulation** in order to start setting up the simulation. A new simulation creating window will pop up. Rename it to **FW Standard Sim** (optional) and click **Create** in order to create a new simulation.

### Analysis type

 ![](https://www.simscale.com/forum/uploads/default/original/2X/6/6c689e7de2a3dd71a449ed6f26a3becab4395d8c.png)

In **Analysis Type** , switch to **Fluid dynamics** and then select **Incompressible**. You don’t have to change any properties here.

Click **Save** to select this analysis type.

Once you save the analysis type, you will see the expanded navigator tree. All the red entities shows that they must be set up in order to perform a successful simulation run.

### Domain

 ![](https://www.simscale.com/forum/uploads/default/original/2X/c/cb491aefab891ba2fff16d19831d7b4075b1035b.png)

Next you have to select a domain on which this simulation will be performed. Proceed to **Domain** and select **FW-Standard-Mesh** and click **Save**.

After a while you will see the loaded mesh of the selected domain in the viewer. For the easier mesh handling, it is recommended to switch to the **surfaces** render mode in the top viewer bar.

### Material

 ![](https://www.simscale.com/forum/uploads/default/original/2X/d/ddb9d5da0b5784245ae6d4553fce15b4af0e8cd7.png)

Next we have to define the fluid material. Go to **Materials** and click on **+New** to create a new material.

 ![](https://www.simscale.com/forum/uploads/default/original/2X/0/0ff172738e8e0bd668ac685f3eecaa332173b283.png)

Click on **Import from material library** to import the desired material from the material database.

 ![](https://www.simscale.com/forum/uploads/default/original/2X/c/c787399902159f03eed2ad03d7b668f605731ede.png)

Select **Air** and click **Save** to import this material directly from the library.

 ![](https://www.simscale.com/forum/uploads/default/original/2X/a/af70cf948bea3aa1dcb47a099864891847410c26.png)

Select **region0** under _Assignment_ and then click **Save** in order to define the material for this region.

### Initial Conditions

Pressure and velocity we will leave as the default set by SimScale.

 ![](https://www.simscale.com/forum/uploads/default/original/2X/2/25c28b60aecace448bdc2b848209773887961262.png)

Go to **k** and change the **Turbulent kinetic energy value [m²/s²]** value to **0.24** and click **Save**

 ![](https://www.simscale.com/forum/uploads/default/original/2X/4/49d88c7063b2e88dae83cec0681bc3c0b528468c.png)

Next go to **Omega** and change **Specific turbulence dissipation rate [1/s]** to **44.7** and click **Save**

The two settings you just modified are associated to the turbulence model that will be applied to this simulation (K-Omega SST). Turbulence is a highly complex process with irregular, chaotic, and unsteady 3D phenomenon. We would need an extremely fine mesh and a huge amount of computational power to correctly simulate it, so the standard process is to apply a model that mathematically predicts this turbulent behavior.

### Boundary Conditions

This is one of the most important parts of the simulation set-up. Boundary conditions are how we tell the platform how each thing behaves. So for example where does the air go in and where does it go out? With what speed does the air go into the domain and in what direction? Is the air being slowed down by something (like the wing)? This is what you’ll do now.

 ![](https://www.simscale.com/forum/uploads/default/original/2X/d/dda6474928cc6c24bfd45c7fdd04324899b24bb3.png)

Go to **Boundary Conditions** and click **+New** in order to create a new boundary condition.

#### 1. Inlet

 ![](https://www.simscale.com/forum/uploads/default/original/2X/6/66b2c1634acbf528ca6575691a318702b2f000e7.png)

Rename the newly created boundary condition to **Inlet** (optional).

Make sure that the _Type_ is **Velocity Inlet** and that under _Velocity_ it says **Fixed value**. Change the **x value [m/s]** to **20**

Select the front surface of the domain from the viewer and under _Assignment_ you should see **boundingBox3**.

Click **Save** to define the inlet boundary condition.

#### 2. Outlet

 ![](https://www.simscale.com/forum/uploads/default/original/2X/c/c9fb4140a4ab589ba79df85aa8b5f57233bb0b1e.png)

Create a new Boundary Condition and name it **Outlet** (optional).

Change _Type_ to **Pressure Outlet** and select the back surface of the domain. Under _Assignment_ you should see **boundingBox4**.

Click **Save** to define the outlet boundary condition.

#### 3. Sides

 ![](https://www.simscale.com/forum/uploads/default/original/2X/0/0f529daa876f6c5f7a47d8fa9bd1a6c14b4cae43.png)

Create a new Boundary Condition and name it **Sides** (optional).

Change _Type_ to **Wall** and **Velocity** to **Slip**.

Select the side face (away from the wing) and the top face of the bounding box. Under _Assignment_ you should see **boundingBox6** and **boundingBox1**.

Click **Save** to define the boundary condition for the sides.

#### 4. Symmetry

 ![](https://www.simscale.com/forum/uploads/default/original/2X/1/132158832701792dc6ab562a85bf7bbb6d70666a.png)

Next we will define the symmetry condition. This is what tells the simulation that in reality we are running a complete wing. Create a new Boundary Condition and name it **Symmetry** (optional).

Change _Type_ to **Symmetry** and select the side face on the inner side of the wing (where it was cut) ( **boundingBox2** ).

Click **Save** to define the symmetry boundary condition.

#### 5. Floor

 ![](https://www.simscale.com/forum/uploads/default/original/2X/d/deedb677cbf974473ba247c58c9071c7ce095b45.png)

Create a new boundary condition and rename it to **Floor** (optional).

Change _Type_ to **Wall** and under _Velocity_ select **Moving wall velocity**. Change the **x value [m/s]** to **20**. With this you’re now saying that the floor also moves past the car (maintaining the condition that there **is** relative motion between the car and the floor and there **isn’t** relative motion between the air and the floor.

Select the floor of the bounding box domain and under _Assignment_ you should see **boundingBox5**.

Click **Save** to define the floor boundary condition.

#### 6. Wing

 ![](https://www.simscale.com/forum/uploads/default/original/2X/f/f73a4b0cf5da7f17b6ae8bd92e045fe011ae8885.png)

Finally, we will define the boundary condition for the wing. Create a new boundary condition and rename it to **Wing** (optional).

Change _Type_ to **Wall** and _Velocity_ to **No-slip**. Also, make sure under _Wall treatment_ it says **Wall function**.

With this _No-slip_ condition you are specifying that there is friction between the car and the air and thus a boundary layer will be formed.

Make sure you hide the bounding box by using the navigator on the right. Select all the wing.

Click **Save** to define the boundary condition for the wing.

### Numerics

 ![](https://www.simscale.com/forum/uploads/default/original/2X/f/f598786646545bbe3a30cef2d704a84ec1a4cb96.png)

After defining all the boundary conditions, we will proceed to set up the numerics for our simulation. Go to **Numerics** and scroll down until you reach **Solver**.

Under _Solver_, change **[U] velocity solver** to **Smooth solver**. Expand **Details** and change **Smoother** to **symGaussSeidel** and **Absolute tolerance** to **1e-7**.

Do similar changes for **[k] Turbulent kinetic energy solver** and **[omega] Specific turbulence dissipation solver**.

Click **Save** to register your changes.

### Simulation Control

 ![](https://www.simscale.com/forum/uploads/default/original/2X/4/470320eb3e37d30e873ce6d3aab2712c48d2605c.png)

Next we will define the our simulation interval and steps that needs to be recorded. Go to **Simulation Control** and change **End time value [s]** to **1500**.

Expand **Details** under **Write control** and change **Write interval (simulation time steps)** to **1500**.

Next change **Number of computing cores** and **Maximum runtime [s]** to **32** and **120,000** respectively. The **Maximum runtime [s]** is set too high just to be on a safe side, because if the simulation runs for longer than that time it is cancelled.

If you are on the _Professional Account Trial_ the setting for **Maximum Runtime** will be too high for the simulation to run. You can change it to **12,000 s** or contact us so that we can change your account to a free community plan.

Please take not that if you are on the _Professional Account Trial_ you will not be able to through all the workshop sessions, so it is recommended to change your account to the Community Plan. You can do this by contacting us directly.

Click **Save** to register your changes.

### Result Control

As our last step before running the simulation, we will create result control items in order to get graphical data sets of interest. These control items allow us to see when a simulation has reached steady state (when forces become constant) and it also lets us see things like the lift and drag of the wing.

 ![](https://www.simscale.com/forum/uploads/default/original/2X/c/c49a710cdb2cc23a9c07ab70d3c444f1bd54c6cd.png)

Go to **Result Control** in the navigator. We will create the result control item for the forces and moments. Click **New** next to **Forces and Moments**.

#### 1. Main Wing

 ![](https://www.simscale.com/forum/uploads/default/original/2X/5/59e2d5c62af120a83f8b44ef2a45ba5b92982fe8.png)

A new force and moment result control item will be created. Rename it to **Wing main** (optional).

Then change **x value [m]** to **-1.4** , **z value [m]** to **-0.47** , and **Write interval (simulation time steps)** to **10**.

Select the main wing and under _Faces for force calculation_ you should see **FWing**.

#### 2. Flap

 ![](https://www.simscale.com/forum/uploads/default/original/2X/5/566067ff07bd62259f9f7414f742beae73e47ed0.png)

Create another force and moment result control item and rename it to **Flap** (optional). Change the same values as defined above but this time select the flap and you should see **Flap** under _Faces for force calculation_.

Click **Save** to save your changes.

#### 3. Field Calculations

 ![](https://www.simscale.com/forum/uploads/default/original/2X/2/20e43f4e01f83356fcb7a34cc179392ae53fb067.png)

Next, we will create the field calculation items. For this go back to **Result Control** and click **New** next to **Field calculations**.

_ **Y-Plus** _

 ![](https://www.simscale.com/forum/uploads/default/original/2X/f/f43972ca9d16f7fc06cc930d92f361b6abec7e80.png)

Rename the newly created field calculation item to **Yplus** (optional).

Change the **Type** to **Turbulence** and click **Save** to register your changes.

_ **Wall Shear Stress** _

 ![](https://www.simscale.com/forum/uploads/default/original/2X/d/dc4695737824436edda14a9760663b1b2ba9f9c8.png)

Create another field calculation item and rename it to **WallShearStress** (optional).

Change the **Type** to **Wall fluxes** and click **Save** to register your changes.

### Simulation Runs

Once all the above steps are defined, we will proceed to create our first simulation run.

 ![](https://www.simscale.com/forum/uploads/default/original/2X/0/02f494e1ddf24914fe90a667fc0549a7f51635d8.png)

Go to **Simulation Runs** and click on **New**.

A window will pop up, give a reasonable name to the run e.g. **Run-Standard** in this case (optional) and click **Start** to initialize this run. The simulation run can take up to **~180 minutes (~3 hrs.)**.

### Additional Simulation Runs

 ![](https://www.simscale.com/forum/uploads/default/original/2X/6/6c95ebf0297d2913e889025d45f67ac43d87fb6d.png)

While the first simulation job is running, take advantage of parallel computing and proceed to start setting up all the other configuration(s). You don’t have to perform all the simulation set up operations again from scratch. Just duplicate the already created simulation by right clicking on it and then click **Duplicate**.

Rename the duplicated simulation to **FW-High Donwforce-Sim** and assign your new domain to the duplicated simulation under **Domain**.

 ![](https://www.simscale.com/forum/uploads/default/original/2X/e/ea5be8cd7eaa598d42fedcbe9d2e3cf7fb18f0d7.png)

Then click **Save**. Now you have to just assign back all the entities to the material, boundary conditions and result control force plot items and then start the simulation job.

* * *

## Recommendations About Comments

If you run into issues during your process, before adding a comment to the thread please consider the following:

1. Go over the tutorial one last time and compare it to your setup. Is everything the same?
2. Go over the existing comments. Maybe someone has had the same problem and it’s already solved.
3. Is there an actual error? Or is it taking a long time to load?  
a. If it seems to be a loading issue, please give it some time or refresh the page. Sometimes due to the internet connection the platform may seem slow.

If it’s a new issue that you can’t solve, please outline the issue as **specifically** as possible and include a link to your project. This will help us figure out what is going on faster and thus we can get back to you faster.

* * *

## Continue to part 2 of the tutorial:

[Step-by-Step Tutorial Session 1 - Front Wing Design Study (Part 2)](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-2/79155)

---

<div class="post-metadata">

**Author:** ![rishav997](https://www.simscale.com/forum/user_avatar/www.simscale.com/rishav997/32/16270_2.png) [@rishav997](https://www.simscale.com/forum/u/rishav997)\
**Post date:** [September 14, 2017, 7:53pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/2 "2017-09-14T19:53:07Z")

</div>

> [@drodriguez32](#):
>
> o Region refinement and then under Refinement levels change Level to 3

in the Region, refinement distance is not specified. Hence, I have take 0.001m.

---

<div class="post-metadata">

**Author:** ![jousefm](https://www.simscale.com/forum/user_avatar/www.simscale.com/jousefm/32/34908_2.png) [@jousefm](https://www.simscale.com/forum/u/jousefm)\
**Post date:** [September 14, 2017, 9:37pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/3 "2017-09-14T21:37:04Z")

</div>

Hi @rishav997!

In the picture it says **1** for the distance.

 ![Mesh refinement 3](https://www.simscale.com/forum/uploads/default/original/2X/a/aadaecd5603359f50fc39c705a1304478cf66a87.png)

Happy SimScaling!

Jousef

---

<div class="post-metadata">

**Author:** ![drodriguez32](https://www.simscale.com/forum/user_avatar/www.simscale.com/drodriguez32/32/14276_2.png) [@drodriguez32](https://www.simscale.com/forum/u/drodriguez32)\
**Post date:** [September 15, 2017, 7:36am UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/4 "2017-09-15T07:36:15Z")

</div>

Hey @rishav997,

In this case for the distance you don’t have to change anything. SimScale sets some default values when you create attributes (either for the mesh or the simulation), so unless it’s specified in the tutorial you don’t really need to change those defaults! 😃

Everything should be referenced in the instructions, but it’s also good to take a look at the screenshots just to double check that your set up is correct! 🙂

I hope you enjoy the tutorial! Happy SimScaling,

Diego

---

<div class="post-metadata">

**Author:** ![AleDaldox](https://www.simscale.com/forum/letter_avatar/aledaldox/32/6_449c533f586939b6e5f246632a46421f.png) [@AleDaldox](https://www.simscale.com/forum/u/AleDaldox)\
**Post date:** [September 15, 2017, 1:27pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/5 "2017-09-15T13:27:02Z")

</div>

![48](https://www.simscale.com/forum/uploads/default/original/2X/a/ace6404456f1f4fa5dd5be70b5eca865d33597f4.png)  
I’m starting the Standard wing simulation, but this message shows up. What should I do?

---

<div class="post-metadata">

**Author:** ![jousefm](https://www.simscale.com/forum/user_avatar/www.simscale.com/jousefm/32/34908_2.png) [@jousefm](https://www.simscale.com/forum/u/jousefm)\
**Post date:** [September 15, 2017, 1:40pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/6 "2017-09-15T13:40:20Z")

</div>

Hi @AleDaldox!

Feel free to share the project with me. I can run it for you if you like.

Cheers!

Jousef

---

<div class="post-metadata">

**Author:** ![drodriguez32](https://www.simscale.com/forum/user_avatar/www.simscale.com/drodriguez32/32/14276_2.png) [@drodriguez32](https://www.simscale.com/forum/u/drodriguez32)\
**Post date:** [September 15, 2017, 1:46pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/7 "2017-09-15T13:46:08Z")

</div>

Hey @AleDaldox,

So how this setting works is that it will cut a simulation if it runs for longer than you specified there. That’s very useful when you have new simulations that you don’t know for how long they will run so that you can keep your core hours safe. What we typically do is specify a number that is way above the time we expect the simulation to be solved in so that the platform doesn’t cut them short and we can get results.

What’s happening right now is that because you’re on the professional account trial you get 200 core hours. Using 32 cores that means that you have a maximum runtime of 22,500 s (way below the value in the tutorial). This can be solved in two ways:

1. You can change the maximum runtime to around 8,000 s (a bit more than two hours) which should still keep your simulation safe (as it’s supposed to be done in less than 2 hours)
2. We can change your account to a free community plan where all your projects will be public, but you get 3,000 core hours (which means you could use a maximum runtime of up to 337,500 s)

Please let us know if you would like to change your account or if you go with the first alternative 🙂

Hope this helped!

Best,  
Diego

---

<div class="post-metadata">

**Author:** ![AleDaldox](https://www.simscale.com/forum/letter_avatar/aledaldox/32/6_449c533f586939b6e5f246632a46421f.png) [@AleDaldox](https://www.simscale.com/forum/u/AleDaldox)\
**Post date:** [September 15, 2017, 2:37pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/9 "2017-09-15T14:37:51Z")

</div>

Dear @drodriguez32,

I think the second one is the best option. I will be grateful if you switch my account to the right plan (the free community one), so that I can use SimScale for the assignment autonomously.

Thanks for the help!

Ale

---

<div class="post-metadata">

**Author:** ![drodriguez32](https://www.simscale.com/forum/user_avatar/www.simscale.com/drodriguez32/32/14276_2.png) [@drodriguez32](https://www.simscale.com/forum/u/drodriguez32)\
**Post date:** [September 15, 2017, 2:55pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/10 "2017-09-15T14:55:50Z")

</div>

Hi @AleDaldox,

You should have just received an email to change your account to the community plan. If you have any projects set to _private_ you need to make them public before you can work on them!

Cheers,

Diego

---

<div class="post-metadata">

**Author:** ![AleDaldox](https://www.simscale.com/forum/letter_avatar/aledaldox/32/6_449c533f586939b6e5f246632a46421f.png) [@AleDaldox](https://www.simscale.com/forum/u/AleDaldox)\
**Post date:** [September 15, 2017, 3:11pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/11 "2017-09-15T15:11:11Z")

</div>

Hi @drodriguez32,

I followed your instructions and everything worked as predicted.  
I’m looking forward to starting my very first simulation now.

Thank you for the prompt support!  
Best,  
Ale

---

<div class="post-metadata">

**Author:** ![viasevoli](https://www.simscale.com/forum/letter_avatar/viasevoli/32/6_449c533f586939b6e5f246632a46421f.png) [@viasevoli](https://www.simscale.com/forum/u/viasevoli)\
**Post date:** [September 15, 2017, 3:31pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/12 "2017-09-15T15:31:31Z")

</div>

It’s too slow, doesn’t work …It’s an internet problem or what ?

---

<div class="post-metadata">

**Author:** ![Vmarotta](https://www.simscale.com/forum/letter_avatar/vmarotta/32/6_449c533f586939b6e5f246632a46421f.png) [@Vmarotta](https://www.simscale.com/forum/u/Vmarotta)\
**Post date:** [September 15, 2017, 3:40pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/13 "2017-09-15T15:40:30Z")

</div>

It’s true, the simulation and the duplication of the mesh are very slow.I have this problem too.

---

<div class="post-metadata">

**Author:** ![dond](https://www.simscale.com/forum/letter_avatar/dond/32/6_449c533f586939b6e5f246632a46421f.png) [@dond](https://www.simscale.com/forum/u/dond)\
**Post date:** [September 15, 2017, 3:59pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/14 "2017-09-15T15:59:10Z")

</div>

While running the first meshing operation I got some error messages:  
Illegal triangles were found after surface tesselation. There could be a problem with the CAD geometry. Trying to proceed [SimScale](https://www.simscale.com/dashboard/anyway).  
The tesselated surface is not closed. There could be a problem with the CAD geometry (such as self-intersections). Please inspect your geometry. Trying to proceed anyway.

This appears to bean error in the base design. Should I restart from scratch or is there a fix?  
I’ll go back and see if there are any other messages. None yet but still computing at the 30 minute point

---

<div class="post-metadata">

**Author:** ![czhang](https://www.simscale.com/forum/user_avatar/www.simscale.com/czhang/32/16181_2.png) [@czhang](https://www.simscale.com/forum/u/czhang)\
**Post date:** [September 15, 2017, 4:29pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/15 "2017-09-15T16:29:38Z")

</div>

Hi, when I got the step for Proceed to Domain and select FW-Standard-Mesh and click Save.  
I found that there is no mesh avaliable in my list and I dont have a Topological Entity Sets like in the tutorial picture.

 ![com-2017-09-15-17-28-45-051](https://www.simscale.com/forum/uploads/default/original/2X/0/0c33c816e30b2e2a4dffef6b1414b2811c75f51d.png)

---

<div class="post-metadata">

**Author:** ![mpoulter](https://www.simscale.com/forum/user_avatar/www.simscale.com/mpoulter/32/30986_2.png) [@mpoulter](https://www.simscale.com/forum/u/mpoulter)\
**Post date:** [September 15, 2017, 4:29pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/16 "2017-09-15T16:29:50Z")

</div>

I’m using a community account. How do i copy the project to make it public? got all the way to the operations step and says the file is private.  
thanks

---

<div class="post-metadata">

**Author:** ![czhang](https://www.simscale.com/forum/user_avatar/www.simscale.com/czhang/32/16181_2.png) [@czhang](https://www.simscale.com/forum/u/czhang)\
**Post date:** [September 15, 2017, 4:35pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/18 "2017-09-15T16:35:33Z")

</div>

U can open the Setting (Gear shape) which is right side of the Sharing, and open that u can find ‘Make a copy’. And create a pubilc one , is that help?

---

<div class="post-metadata">

**Author:** ![dond](https://www.simscale.com/forum/letter_avatar/dond/32/6_449c533f586939b6e5f246632a46421f.png) [@dond](https://www.simscale.com/forum/u/dond)\
**Post date:** [September 15, 2017, 4:41pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/19 "2017-09-15T16:41:14Z")

</div>

It, apparently, finished successfully. So, I will proceed…

---

<div class="post-metadata">

**Author:** ![jousefm](https://www.simscale.com/forum/user_avatar/www.simscale.com/jousefm/32/34908_2.png) [@jousefm](https://www.simscale.com/forum/u/jousefm)\
**Post date:** [September 15, 2017, 8:18pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/20 "2017-09-15T20:18:04Z")

</div>

Hi @viasevoli & @Vmarotta!

Do you still have the problems with a slow simulation?

Best,

Jousef

---

<div class="post-metadata">

**Author:** ![jousefm](https://www.simscale.com/forum/user_avatar/www.simscale.com/jousefm/32/34908_2.png) [@jousefm](https://www.simscale.com/forum/u/jousefm)\
**Post date:** [September 15, 2017, 8:18pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/21 "2017-09-15T20:18:52Z")

</div>

Hi @dond!

No worries about that warning. You may still run your simulation. Did yours finish already?

P.S.: Sorry saw your post too late. Glad it worked out! 🙂

Best,

Jousef

---

<div class="post-metadata">

**Author:** ![jousefm](https://www.simscale.com/forum/user_avatar/www.simscale.com/jousefm/32/34908_2.png) [@jousefm](https://www.simscale.com/forum/u/jousefm)\
**Post date:** [September 15, 2017, 8:19pm UTC](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755/22 "2017-09-15T20:19:48Z")

</div>

Hi there @czhang!

Did you already figure out the issue or fixed it by yourself? If not please feel free to share the project with me and I will have a look at it! 👍

All the best!

Jousef

[Next page](https://www.simscale.com/forum/t/step-by-step-tutorial-session-1-front-wing-design-study-part-1/78755.md?page=2)
