# Discrepancy between Abaqus and SimScale for simple uniaxial 3D hex-mesh bar: rigid body modes and stress distribution

**URL:** <https://www.simscale.com/forum/t/discrepancy-between-abaqus-and-simscale-for-simple-uniaxial-3d-hex-mesh-bar-rigid-body-modes-and-stress-distribution/101030>\
**Category:** Solid Mechanics / FEA\
**Created:** [May 11, 2026, 10:19am UTC](https://www.simscale.com/forum/t/discrepancy-between-abaqus-and-simscale-for-simple-uniaxial-3d-hex-mesh-bar-rigid-body-modes-and-stress-distribution/101030 "2026-05-11T10:19:23Z")\
**Posts on this page:** 2\
**Page:** 1

<div class="post-metadata">

**Author:** ![biswabhanu\_puh](https://www.simscale.com/forum/letter_avatar/biswabhanu_puh/32/6_449c533f586939b6e5f246632a46421f.png) [@biswabhanu\_puh](https://www.simscale.com/forum/u/biswabhanu_puh)\
**Post date:** [May 11, 2026, 10:19am UTC](https://www.simscale.com/forum/t/discrepancy-between-abaqus-and-simscale-for-simple-uniaxial-3d-hex-mesh-bar-rigid-body-modes-and-stress-distribution/101030/1 "2026-05-11T10:19:23Z")

</div>

I am comparing a very simple uniaxial bar problem between Abaqus and SimScale and observing a discrepancy that I would like to understand better.

## Problem setup

- Simple rectangular 3D bar

- Linear elastic steel

- Pure hexahedral mesh in SimScale:

- Uniform pressure/load applied in X direction on right face

- Left face constrained

The mesh in SimScale reports:

- Mesh order: 2nd

- Number of hexahedra: 160

- Number of triangles: 0

So this appears to be a genuine structured hex mesh.

## Expectation

For ideal uniaxial loading, I expect approximately uniform axial stress:

σxx = F/A

especially away from the constrained edge.

## Observation in Abaqus

Using a structured hex mesh:

- the stress field becomes almost perfectly uniform (~25 MPa)

- even when only UX = 0 is prescribed on the left face, Abaqus solves without singularity/convergence issues

## Observation in SimScale

Even with the pure hex mesh:

- I still observe stress disturbances/gradients near the constrained edge

- if I constrain only UX = 0, the solver reports singularity/convergence issues

- the simulation only runs robustly when additional constraints (UY/UZ) are added

This surprised me because the same conceptual setup runs smoothly in Abaqus.

## My questions

1. Is this primarily due to differences in:

2. Does SimScale require stricter removal of rigid body modes for full 3D solid mechanics problems?

3. Is Abaqus internally stabilizing or regularizing this near-singular system automatically?

4. Are the stress gradients near the support physically expected due to Saint-Venant / Poisson constraint effects, while Abaqus visually smooths them more aggressively?

I am asking partly because I plan to use this example pedagogically to teach:

- structured vs unstructured meshes,

- convergence,

- and boundary-condition effects.

Any clarification would be greatly appreciated.

---

<div class="post-metadata">

**Author:** ![Ricardopg](https://www.simscale.com/forum/user_avatar/www.simscale.com/ricardopg/32/26909_2.png) [@Ricardopg](https://www.simscale.com/forum/u/Ricardopg)\
**Post date:** [May 15, 2026, 10:35am UTC](https://www.simscale.com/forum/t/discrepancy-between-abaqus-and-simscale-for-simple-uniaxial-3d-hex-mesh-bar-rigid-body-modes-and-stress-distribution/101030/3 "2026-05-15T10:35:28Z")

</div>

Hi,

For this case I’d normally expect a constraining strategy like the one from [this validation case](https://www.simscale.com/docs/validation-cases/3d-triaxial-load-secondary-creep-nafems-test-6a/), which would give you a uniform stress.

 ![image](https://www.simscale.com/forum/uploads/default/original/3X/d/d/dd7cff6e8b494dc78ec783ee51ec74706b7a441f.png)

Cheers
