# Accurate simulation?

**URL:** <https://www.simscale.com/forum/t/accurate-simulation/92739>\
**Category:** Project Support\
**Created:** [May 13, 2021, 12:23pm UTC](https://www.simscale.com/forum/t/accurate-simulation/92739 "2021-05-13T12:23:16Z")\
**Posts on this page:** 13\
**Page:** 1

<div class="post-metadata">

**Author:** ![FrankTheTank](https://www.simscale.com/forum/user_avatar/www.simscale.com/frankthetank/32/39326_2.png) [@FrankTheTank](https://www.simscale.com/forum/u/FrankTheTank)\
**Post date:** [May 13, 2021, 12:23pm UTC](https://www.simscale.com/forum/t/accurate-simulation/92739/1 "2021-05-13T12:23:16Z")

</div>

Hi I just created a new simulation, I was wondering if this project is accurate or close to accurate? I think it might be more accurate than the past, because one, I used region refinments to an extent, two I used symmetry on this simulation, three I made the mesh better quality than the last version. It also took less time to come up with a flat out result please take a look, here is the link [https://www.simscale.com/workbench/?pid=450324700395851699&mi=spec%3A3abe0a78-89f7-4fd8-b17b-481e0e76f3d7%2Cservice%3ASIMULATION%2Cstrategy%3A17](https://www.simscale.com/workbench/?pid=450324700395851699&mi=spec%3A3abe0a78-89f7-4fd8-b17b-481e0e76f3d7%2Cservice%3ASIMULATION%2Cstrategy%3A17)

Thank you for your time and help,  
Frank lucci

---

<div class="post-metadata">

**Author:** ![tsite](https://www.simscale.com/forum/user_avatar/www.simscale.com/tsite/32/47909_2.png) [@tsite](https://www.simscale.com/forum/u/tsite)\
**Post date:** [May 13, 2021, 12:31pm UTC](https://www.simscale.com/forum/t/accurate-simulation/92739/2 "2021-05-13T12:31:43Z")

</div>

Hey Frank,

To begin with, you can check whether the simulation reached a converged state according to this guide: [How to Check Convergence of a CFD Simulation? | SimScale](https://www.simscale.com/knowledge-base/how-to-check-convergence-of-a-cfd-simulation/)  
The boundary conditions seem just fine 🙂 Make sure to check the y plus value in the solution fields as well.  
[How to Control and Analyze Y+ in Meshing Simulation | SimScale](https://www.simscale.com/knowledge-base/how-to-control-y-when-meshing/)

Best regards,  
Fillia

---

<div class="post-metadata">

**Author:** ![FrankTheTank](https://www.simscale.com/forum/user_avatar/www.simscale.com/frankthetank/32/39326_2.png) [@FrankTheTank](https://www.simscale.com/forum/u/FrankTheTank)\
**Post date:** [May 13, 2021, 12:59pm UTC](https://www.simscale.com/forum/t/accurate-simulation/92739/3 "2021-05-13T12:59:20Z")

</div>

Hello again, I have decided to run the simulation a bit more to make the convergence a bit more perfect. I can’t get my head around the y plus value. Is there a general rule of thumb I can use for the y plus value?

Thank you again,  
Frank  
Lucci

---

<div class="post-metadata">

**Author:** ![tsite](https://www.simscale.com/forum/user_avatar/www.simscale.com/tsite/32/47909_2.png) [@tsite](https://www.simscale.com/forum/u/tsite)\
**Post date:** [May 13, 2021, 1:03pm UTC](https://www.simscale.com/forum/t/accurate-simulation/92739/4 "2021-05-13T13:03:25Z")

</div>

Check here: [There are 5 levels of region refinements, how much should each one be - #3 by jairogut](https://www.simscale.com/forum/t/there-are-5-levels-of-region-refinements-how-much-should-each-one-be/92692/3)

This should be helpful 🙂

Best regards,  
Fillia

---

<div class="post-metadata">

**Author:** ![FrankTheTank](https://www.simscale.com/forum/user_avatar/www.simscale.com/frankthetank/32/39326_2.png) [@FrankTheTank](https://www.simscale.com/forum/u/FrankTheTank)\
**Post date:** [May 13, 2021, 1:25pm UTC](https://www.simscale.com/forum/t/accurate-simulation/92739/6 "2021-05-13T13:25:09Z")

</div>

So the y+ is 30 to 100 in the finest spot of the mesh or the first and most refined region, what should be the y+ of the 2nd region refinment and the flow region? I’d don’t understand.

Sorry for the trouble,  
Frank  
Lucci

---

<div class="post-metadata">

**Author:** ![ggiraldof](https://www.simscale.com/forum/user_avatar/www.simscale.com/ggiraldof/32/30298_2.png) [@ggiraldof](https://www.simscale.com/forum/u/ggiraldof)\
**Post date:** [May 13, 2021, 1:30pm UTC](https://www.simscale.com/forum/t/accurate-simulation/92739/7 "2021-05-13T13:30:46Z")

</div>

Hi Frank!

Y+ is only computed for the walls, especially those with wall modeling boundary conditions (function or full resolution). Please refer to this article for some background:

> [@What is y+ (yplus)?](https://www.simscale.com/forum/t/what-is-y-yplus/82394):
>
> There can never be a last word in regard to the axioms of any physical theory. All we can ask of them is that they lead to conclusions in agreement with observation. Sooner or later more refined observations will find the weak point in any set of physical axioms. Nature is far too complicated to be completely described in a few equations. - J.L. Synge (1938) \underline{\textbf{Introduction}} Before World War II, Johann Nikuradse (known from the Nikuradse Diagram) took a bunch of velocity meas…

---

<div class="post-metadata">

**Author:** ![FrankTheTank](https://www.simscale.com/forum/user_avatar/www.simscale.com/frankthetank/32/39326_2.png) [@FrankTheTank](https://www.simscale.com/forum/u/FrankTheTank)\
**Post date:** [May 13, 2021, 3:03pm UTC](https://www.simscale.com/forum/t/accurate-simulation/92739/9 "2021-05-13T15:03:22Z")

</div>

So do you have to have the y+ correct for an accurate simulation? Or can it be close to accurate and the simulation will still be accurate?

---

<div class="post-metadata">

**Author:** ![ggiraldof](https://www.simscale.com/forum/user_avatar/www.simscale.com/ggiraldof/32/30298_2.png) [@ggiraldof](https://www.simscale.com/forum/u/ggiraldof)\
**Post date:** [May 13, 2021, 3:07pm UTC](https://www.simscale.com/forum/t/accurate-simulation/92739/10 "2021-05-13T15:07:35Z")

</div>

The correct y+ guarantees that the wall boundary condition is giving valid results.

If you are not interested in the accuracy of the flow fields (velocity and pressure) at the walls, but for example in regions far from them, then I guess you do not have to worry about perfect y+ values. Otherwise, you do.

---

<div class="post-metadata">

**Author:** ![FrankTheTank](https://www.simscale.com/forum/user_avatar/www.simscale.com/frankthetank/32/39326_2.png) [@FrankTheTank](https://www.simscale.com/forum/u/FrankTheTank)\
**Post date:** [May 13, 2021, 3:54pm UTC](https://www.simscale.com/forum/t/accurate-simulation/92739/12 "2021-05-13T15:54:54Z")

</div>

So if it is a symmetrical type simulation do you have to have good y+ values or can you have ok y+ values and get accurate results?

---

<div class="post-metadata">

**Author:** ![ggiraldof](https://www.simscale.com/forum/user_avatar/www.simscale.com/ggiraldof/32/30298_2.png) [@ggiraldof](https://www.simscale.com/forum/u/ggiraldof)\
**Post date:** [May 13, 2021, 3:57pm UTC](https://www.simscale.com/forum/t/accurate-simulation/92739/13 "2021-05-13T15:57:30Z")

</div>

Please read the reference and analyse with care!

Y+ is only important in no-slip walls

---

<div class="post-metadata">

**Author:** ![ggiraldof](https://www.simscale.com/forum/user_avatar/www.simscale.com/ggiraldof/32/30298_2.png) [@ggiraldof](https://www.simscale.com/forum/u/ggiraldof)\
**Post date:** [May 14, 2021, 4:26pm UTC](https://www.simscale.com/forum/t/accurate-simulation/92739/16 "2021-05-14T16:26:50Z")

</div>

If the y+ is correct according to the selected wall model, then this point is checked.

The next step to assure the accuracy of the simulation would be to perform a mesh independence analysis.

---

<div class="post-metadata">

**Author:** ![FrankTheTank](https://www.simscale.com/forum/user_avatar/www.simscale.com/frankthetank/32/39326_2.png) [@FrankTheTank](https://www.simscale.com/forum/u/FrankTheTank)\
**Post date:** [May 14, 2021, 9:37pm UTC](https://www.simscale.com/forum/t/accurate-simulation/92739/18 "2021-05-14T21:37:14Z")

</div>

Hi again I looked every were and I couldn’t find it, could you describe what it is and how to do it?  
Thank you,  
Frank  
Lucci

---

<div class="post-metadata">

**Author:** ![tsite](https://www.simscale.com/forum/user_avatar/www.simscale.com/tsite/32/47909_2.png) [@tsite](https://www.simscale.com/forum/u/tsite)\
**Post date:** [May 27, 2021, 8:59am UTC](https://www.simscale.com/forum/t/accurate-simulation/92739/19 "2021-05-27T08:59:50Z")

</div>

Hey Frank, make sure to add the ‘Turbulence’ under the ‘Field calculations’, so you can check the y+ values in the post-processor after the run.

[Result Control | Simulation Setup | SimScale](https://www.simscale.com/docs/simulation-setup/result-control/#:~:text=Result%20control%20allows%20users%20to,stress%20in%20a%20structural%20analysis).
